• 10S1P 42V 10Ah Li-polymer battery pack
  • 10S1P 42V 10Ah Li-polymer battery pack
  • 10S1P 42V 10Ah Li-polymer battery pack
  • 6000mAH-20000mAH - 10S1P 42V 10Ah Li-polymer battery pack
  • 6000mAH-20000mAH - 10S1P 42V 10Ah Li-polymer battery pack
  • 6000mAH-20000mAH - 10S1P 42V 10Ah Li-polymer battery pack

10S1P 42V 10Ah Li-polymer battery pack

6000mAH-20000mAH

Model: AY-LP10S1P-9759156-10000mAH
Voltage: 42V
Capacity: 10Ah
Size (can be customized): L166* W107* T80mm
Cell Model: 9759156-10Ah

  • Description
  • Get quote
Sender email add: RE: 10S1P 42V 10Ah Li-polymer battery pack
  • 6000mAH-20000mAH

    AY-LP10S1P-9759156-10000mAH

    10S1P 42V 10Ah Li-polymer battery pack 
    Technical Parameters
    Battery pack * 42V 10Ah Li-polymer Battery is made by 10pcs of li-polymer 9759156 10Ah cells
    * In 10S1P configuration
    * Wrap with heavy duty PVC
    Charge Information *Charge voltage: 4.2V±0.05V (4.2V/cell)
    *Charge method: CC/CV (Constant-current and-Voltage with Limited current)
    *Standard charging time: 2A/ 7.5hours    20A/ 1hours   
    (Battery capacity÷charging current×1.5 )
    *Charge current: 20A 
    Dishcharge Information * Maximum discharging current: 40A 
    * Continuous discharge current: 40A 
    * Discharge cut-off voltage: 2.5V (2.5V/cell)
    Protection Information * Protected by one PCM:
    * PCM is installed in the battery pack to balance charging and protect battery
    * Must wait min of 30 minutes afrer battery is fully charged to allow the PCM to perform balance function on all the cells within the pack
    * Maximal continuous charging current: 20A
    * Maximal continuous discharging current: 40A
    * Over-charge& over-discharge detection voltage: 4.2V/2.5V
    * Over-current detection: 140±20A
    Short-circuit Protection Exterior short circuit Automatic recovery
    Intermal resistance / Cycle life ≤200mΩ / ≥500
    Operating Temperature *Standard Charge: 0~+40℃ / *Standard Discharge: -20~+60℃
    Pre-wired * Red=Positive,Black=Negative
    Weight/Dimension around 2.2kgs(including cells,pcm.pvc wires) ; L166* W107* T80mm
    Applications * Apply to industry application, medical devices, etc
    * Replace 12V Nimh battery and 12V Lead acid battery with much clear engergy.
    Warnings * 42V 10Ah Li-polymer Battery should be cut-off at ≥2.5V (2.5V/cell) during
    discharging, and should be stop charging at ≤4.2V(4.2V/cell)during charging.
    * We are not responsible for an damages or losses caused by misuse (included but not
    limited to: Improper charging/discharging, any changes of this battery pack,
    miss-assembling battery packs.)
    * Always pay attention to when charging the battery pack. Battery shall put in a place
    or wrong polarity connection.
    * Please always check battery polarity before connection to device. Never make wrong polarity connection.

Copyright © 2017 AYAA TECHNOLOGY CO.,LTD. All Rights Reserved. Design By Gemelsoft.